TESTING & COSMETIC NOTES: This is a USED WORKING item in GOOD cosmetic condition that IS THOROUGHLY TESTED and is GUARANTEED WORKING This unit powers on and has been reset to a default state, view console log below for more info. Please note, there are scuffs/scratches on the top panel and a screw missing from the front panel, view photo for detail. In the rare situation that this is not the case, we will send a replacement upon safe return of the original item within 30 days of receiving the item.
U-Boot 1.1.3 (Feb 23 2010 - 09:41:55) CPU: AMCC PowerPC 440EPx Rev. A at 660 MHz (PLB=132, OPB=66, EBC=33 MHz) No Security/Kasumi support I2C boot EEPROM enabled Bootstrap Option G - Boot ROM Location I2C (Addr 0x54) Internal PCI arbiter enabled, PCI async ext clock used 32 kB I-Cache 32 kB D-Cache Board: Spike CP I2C: ready DRAM: Initializing DDRSDRAM WARNING: DRAM DIMM in slot 0 has 0 ranks. Only one rank will be used.DQS calibration - Window detected: max_passing_cases = 55 wr_dqs_shift = 94 dll_dqs_delay_X = 32 dll_dqs_delay_X window = 5 - 59 DDR0_09=0x00011d5e DDR0_22=0x03267e0b DDR0_17=0x20005d00 DDR0_18=0x20202020 DDR0_19=0x20202020 Zeroing SDRAM... DONE DDR: 1024 MB POST RAM test disabled. Now running in RAM - U-Boot at: 3fb31000 trap_init : 0x0 system inventory subsystem initialized FLASH: Leda CFI Flash Driver Initialized 4 MB ATA interface setup: io_base=0xf8f00000, port=0x1f0, ctl=0x3f6 PCI: In: serial Out: serial Err: serial Net: Checking system RAM - press any key to stop test Checking memory address: 00100000 System RAM test using Default POST RAM Test succeeded. Set_bootstatus: BS_LOAD_OS, platform_idx = 8 Type run flash_nfs to mount root filesystem over NFS Hit ESC to stop autoboot: 0 Map file at LBA sector 0x1a58b8 ## Booting image at 00400000... Image Name: Linux-18.104.22.168 Image Type: PowerPC Linux Multi-File Image (uncompressed) Data Size: 4267435 Bytes = 4.1 MB Load Address: 00000000 Entry Point: 00000000 Contents: Image 0: 3190918 Bytes = 3 MB Image 1: 1076503 Bytes = 1 MB ## Current stack ends at 0x3FAEFBE0 => set upper limit to 0x00C00000 ## initrd at 0x0070B0D4...
0x00811DEA (len=1076503=0x106D17) Loading Ramdisk to 1fef9000, end 1ffffd17... OK initrd_start = 1fef9000, initrd_end = 1ffffd17 ## Transferring control to Linux (at address 00000000)... Installing Linux 2.6 Kernel Attempting to find a root file system on hda2... INIT: version 2.78 booting Bypassing firmware validation.
INIT: Entering runlevel: 3 Starting Fabric OS Services... Sys_chip_init: class 0 max 24 Done ethsw_ha_enabled = 1 uptime: 4293889148; sup_qid: 0 2017/11/14-16:16:27, [HAM-1004], 8137, CHASSIS, INFO, Brocade7800, Processor reb ooted - Reboot. Wrote 0 leases to leases file. 2017/11/14-16:16:48, [FCR-1069], 8138, FID 128, INFO, ECNSAN02, The FC Routing s ervice is enabled.
2017/11/14-16:16:48, [FCR-1068], 8139, FID 128, INFO, ECNSAN02, The FC Routing s ervice is disabled. All service instances on Active BP_SYSTEM_FPGA_VERSION: 10 2017/11/14-16:16:59, [EM-1034], 8140, CHASSIS, ERROR, Brocade7800, PS 2 set to f aulty, rc=2000e. The item "HP STORAGEWORKS 1606 BASE EXT SAN 16-PORT 8GB FIBER FC GIGABIT ETHERNET SWITCH" is in sale since Tuesday, February 20, 2018. This item is in the category "Computers/Tablets & Networking\Enterprise Networking, Servers\Switches & Hubs\Network Hubs". The seller is "ocdepot" and is located in Santa Ana, California.
This item can be shipped worldwide.